The Conclusions and Recommendations can be combined or, in long reports, presented in separate sections.

Conclusions and recommendations

If there aren’t any recommendations to be manufactured as a result of the project, just call this section Conclusions.

The Conclusions section sums up the key points of your discussion, the essential popular features of your design, or even the significant outcomes of one’s investigation. As the function is to round the story off of assembling your project, it must:

  • be written to relate right to the aims associated with the project as previously mentioned in the Introduction
  • indicate the extent to that your aims have been achieved
  • summarise the findings that are key outcomes or information in your report
  • acknowledge limitations while making suggestions for future work (where applicable)
  • highlight the value or usefulness of one’s work.

The conclusions should relate solely to the aims associated with work:

The goal of this project is to design a cell phone tower for a suburban location..

The cell phone tower presented here could be erected safely in a suburban street.

It takes a total area of no more than 2m 2 l, and has now the safety that is following.

This investigation will review the amount of passengers using the Monash University Clayton-Caulfield inter-campus bus to be able to recommend adjustments into the ongoing service if needed.

Analysis regarding the survey data obtained in this project implies that use of the Clayton-Caulfield inter-campus bus has increased by 24% in the past five years. It is recommended that frequency be increased during peak usage.

The Conclusions section below is from a level 2 Civil Engineering Alternative Designs report presenting two designs for a an overpass bridge. Go through the buttons that are coloured look at comments.

Conclusions

All the two bridge designs Lecturer’s comment:
An elegant beginning for a Conclusions follows on neatly from the discussion that is preceding. In this case, moreover it indicates that the aims associated with project have been met. presented in this report fulfil the criteria specified within the project brief. Both designs Lecturer’s comment:
The main findings or outcomes – in this full case the important thing top features of the designs – are then recapped. incorporate round piers on piled foundations, that are used because the soil conditions are unknown and possibly unstable. Design 1, an easy i-girder that is composite, has the advantage of being manufactured from steel and therefore has longer spans and fewer piers.

Design 2, a super-T beam br >Design 2 Lecturer’s comment:
The significance of the end result – in this situation the last recommendation – is actually stated. is therefore recommended. It offers Lecturer’s comment:
To finish off, the achievement associated with the project is ultius reinforced. An overpass that is affordable superior durability, and fully meets certain requirements regarding the design brief.

Always address limitations and suggest how they may be overcome in the future work. The below that is excerpt through the Conclusions of a study on a project investigating the result of pulsation on heat transfer in horizontal pipe flow.

Experimental results Lecturer’s comment:
Key conclusions drawn from the project. indicated that pulsed flow without flow reversal had no effect that is significant with steady flow. Preliminary experiments with reversed flow, however, clearly indicated increased heat transfer. This might be likely due Lecturer’s comment:
Provide a possible explanation for notable results, especially unexpected ones. to the large disturbances in the hydrodynamic boundary layer as soon as the flow changes direction. Further research Lecturer’s comment:
Recommend further research to handle any extra work you think will be useful. is preferred to determine the most enhancement that is achievable.

It ought to be noted that Lecturer’s comment:
Acknowledge limitations or errors and suggest explanations solutions that are and/or. the experimental results try not to buy into the equations that are theoretical. This can be as a result of deposits which developed within the pipe, or even to thermocouple temperature that is inconsistent. Therefore, regular inspection of this test rig is recommended.

For a rather report that is long it really is acceptable to provide the conclusions and recommendations in point form:

The prototype robot courier presented here has been confirmed to allow you to delivering documents autonomously in an office environment. It offers demonstrated the following the different parts of mobile robotics:

  1. Localisation: The Kalman filter-based localisation algorithm achieved sub-centimeter accuracy under normal operating conditions.
  2. Environment modelling: The occupancy map was updated dynamically to incorporate obstacles not included in the original map.
  3. Path planning: A distance path that is transform-based using obstacle transforms produced a globally optimal local entrapment-free road to the goal.